FAST MINI-LEVEL is designed for making thin-layer leveling screeds with a thickness of 2 to 20 mm on concrete, cement (with or without underfloor heating) and anhydrite surfaces before laying all types of floor coverings, such as: PVC tiles and coverings, parquet, panels, carpet and cork coverings, ceramic tiles and others. It can be applied inside buildings, in such rooms as: living rooms, corridors, offices, lounges, waiting rooms, warehouses, workshops, utility rooms as well as in rooms with high humidity, such as bathrooms.
FAST MINI-LEVEL is a self-leveling floor based on a dry mix of Portland and clay cement, sand, additives and admixtures. After mixing with water, it forms an easily spreading, self-leveling mass. It can be poured by hand or machine. When fully cured, it is resistant to abrasion and high loads.
bag - 25 kg
Product's photo
The surface should be durable, load-bearing and properly seasoned, free from impurities reducing the adhesion of the floor, i.e. grease, dust, bitumen, etc.).
Brittle and flaking layers, remains of paint coats and adhesives should be removed. Widen cracks, dust tme and apply FAST GRUNT U primer, minor defects should be filled with FAST SUPER leveling mortar. Weak surfaces should be strengthened with FAST GRUNT G primer. At least 24 hours before making the screed, the surfaces requiring reduction of water absorption should be primed with FAST GRUNT U. Small cracks in the surface and places exposed to stress concentration should be additionally reinforced with a glass fiber mesh reinforcement. Always make edge dilatations (stick strips of polystyrene or sponge to the walls). If there are expansion joints in the surface, they should be repeated in the floor layer.
The transfer of building structural expansion joints and the size of expansion fields should always be consulted with the designer.
The maximum size of the expansion joint inside the rooms cannot exceed 36 m2. When taking the length and width of the fields, the proportions close to the square should be kept. Antishrinkage dilatations should also be made at room thresholds.
Before pouring the compound, the initial level of the layer thickness should be determined, depending on the existing unevenness of the surface (we refer to the lowest point and the screed must cover the highest point with at least 2 mm). The leveling can be performed by any known method, e.g. with a leveler and a staff, or with the use of a regular, relatively long level. Portable benchmarks are useful at this stage of works, as they definitely facilitate and speed up the work. With a relatively even surface and the expected minimum screed thicknesses, the floors can be poured directly without the above-mentioned steps.
Use a slow-speed drill to mix the contents of the bag with about 5 L of cool, clean water until the mixture is homogeneous and the required consistency is obtained. After waiting 10 minutes, re-mix. Thus prepared amount of FAST MINI-LEVEL should be poured on the surface in one layer, spread with a long steel float or scraper, starting from one of the walls and gradually moving towards the exit. The surface of a freshly poured floor should be deaerated with a spiked roller. Breaks in pouring the floor should not be longer than 20 minutes. Walking is allowed after 6 hours. After 7 days, PVC floor claddings, panels, carpets and cork claddings can be placed on the floor surface, provided that the floor humidity does not exceed 2.5%. Ceramic tiles and other floor claddings can be glued after just two days. Water overdosing changes the parameters of the floor and may lead to cracks. Inaccurate priming and venting may cause air bubbles to appear on the surface.
Tools: low-speed electric mixer, basket mixer, float, scraper bar, spiked roller, soles with spikes, containers, a vessel with a scale for measuring water. Tools should be washed with cold water immediately after use. Implementation recommendations: Observe the appropriate temperature of the surface and air during works as well as during drying of the floor, i.e. +5°C to +25°C.
cements: Portland and clay,mineral fillers, modifiers
about 5 l of water for 25 kg of dry product
Store in factory-sealed packages, in dry rooms, on pallets at a temperature of +5°C to +25°C. The shelf life is 12 months.
The product is irritant and contains cement, becomes alkaline after mixing with water. Avoid direct contact with the skin and protect the eyes. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. Keep away from children.
