Products

Products

ARCHITECT 200

Latex paint with increased resistance to scrubbing. For walls and ceilings

Usage

Intended for painting walls and ceilings inside rooms. It can be used on all types of mineral surfaces, such as cement, cement-lime, gypsum plasters, plasterboards, wallpapers, including fiberglass ones, surfaces coated with a polymer dispersion coating.

Properties

ARCHITECT 200 is an ecological latex paint with good scrub resistance and washability as well as excellent adhesion to mineral  surfaces. Its innovative formula creates a durable coating with a matte finish that diffuses light rays, giving the wall a perfect look. The product is developed using the highest quality raw materials so that your color remains unchanged for years. The paint is available in a wide range of colors according to FAST COLOR SYSTEM.

Package

bucket - 2.7 l

bucket - 4.5 l

bucket - 10 l

Documentation

Product's photo

Surface preparation

The surface must be dry, clean and free from dust and grease. Glossy surfaces must be matted before painting. Repair/fill in all defects and imperfections of the surface and prime them before painting. Remove old, peeling, flaking paint and then prime it with a deep penetrating agent FAST GRUNT G. Nicotine, oil, and run-off stains should be covered with FAST ISOPRO. Prime fresh plasters, coats and plasterboards with FAST GRUNT U. Other raw, absorbent surfaces also need to be primed in advance.

The paint can be used on the following surfaces:

  • cement and cement-lime plasters (after a minimum of 28 days from the date of implementation and humidity not higher than 4%)primed with FAST GRUNT U or FAST GRUNT F.
  • concrete (after more than 28 days from execution and with humidity not higher than 4%) primed with FAST GRUNT U or  FAST GRUNT F 
  • gypsum surfaces (humidity below 1%) primed with FAST GRUNT U or FAST GRUNT F

Preparation and usage method

Mix the contents of the package to ensure the uniformity of the product. Do not thin with water. Do not add lime and do not mix with other paints or primers. Purchase the right amount of product to be able to completely execute the project. Do not paint in conditions of high air humidity. Apply when the ambient temperature and the temperatures of the surface to be painted is between +10°C and +25°C. When purchasing more than one package of the same color, mix the contents of the packages to make the color uniform. In the case of colors
marked as poorly covering and intense in the system, use a FAST GRUNT F primer of a similar color. If you expect there is not enough product to finish the work, finish on the corner or contours of the painted surface. Apply the product using a suitable roller, brush or spray. Paint  thoroughly,  evenly  applying  a  similar  amount  of  product  to  a  specific  area  of  the  wall  each  time,  and  finish  with  a  gentle  vertical movement in one direction. The paint should be applied in two layers. The next layer should be applied after at least 2 hours. Ensure proper
ventilation of the room during painting and drying of the product.

Parameters of airless spray based on the WAGNER - ProSpray 3.23 device

  • nozzle diameter 517-519
  • pressure 190-220
  • bar mesh filter 50
  • thinning max. up to 2% with the first layer

AFTER PAINTING
 
Remove as much paint as possible from the painting tools (roller, brush) before proceeding to washing them in warm soapy water. Wipe up spilled paint immediately with a damp cloth.
 
Instructions for use of the paint coating

 The paint coating acquires its full functional properties (scrub resistance/washability) after complete hardening, i.e. after 28 days from the end of painting.
 
Cleaning of surfaces finished with a coating of latex paint should be carried out with a cloth, sponge or soft brush soaked in water or with an alcohol-free detergent, e.g. dishwashing liquid or soap. This method enables the removal of stains from the paint without the risk of their shining or abrasion of the coating. To remove dirt, agents containing chlorine or bleaches should not be used as they may discolor pigments contained in the paint.
During washing, avoid excessive force and prolonged friction as they may damage the coating.

USE

Depending on the type of substrate, ARCHITECT 200 consumption is from 0.07 to 0.12 l / m².

Technical data

Base unit
l
Base

polymer dispersion with addition of mineral fillers with pigments

Density
about 1.4 kg/m3
Drying time of the first layer
about 2 hours
The number of layers
2
Substrate and ambient temperature
from 10 °C
to 25 °C
Wet scrub resistance
2

Storage and warnings

Store the product in a tightly closed container. Dispose of unused paint properly. Check if there is a collection point for paint waste in your neighborhood. If the amount of paint is left that cannot be reused or stored, do not pour it down the drain. The paint is to be stored and transported in tightly closed, original packaging at temperatures between +5°C and +25°C.


While working, avoid direct contact with the skin and protect the eyes. In case of contact with the eyes, rinse immediately with plenty of water and seek medical advice. Rinse soiled skin immediately with plenty of water.
Keep away from children.